Product Description
This is the high-tech solution to performance handling and control that O.E.M. manufacturers usually just don't offer!
Energy's special formula HYPER-FLEX™ performance polyurethane components, which is higher durometer (firmness) material and re engineered performance-minded components, assures long-lasting performance in all sets. Performance many O.E.M. bushings and mounts just can't offer.
- Get real performance for both on the road and at the track.
- A real must for competition use- or just for that "seat-of-the-pants" fun!
- Increases vehicle stability and control as well as durability.
- Reduces wheel hop and traction loss.
- Proven for many years, by both professional and amateur racers alike.
- Both restores and improves better than new!
- Made of Energy's HYPER-FLEX performance polyurethane.
- Heavy duty metal components are used for increased strength, when applicable.
Includes two Energy Suspension bushings for both sides.
 |
OEM Nissan Power Steering Fluid
starstarstarstarstar (15)
$4.20
OEM Nissan/Infiniti Engine Oil Drain Plug
starstarstarstarstar (4)
$6.01
Z1 Motorsports Zino Air Freshener
starstarstarstarstar_half (56)
$5
Aeromotive 340 LPH Stealth E85 Fuel Pump 11542
$144.95
Dobinsons Frontier / Xterra Leaf Spring Shackle Bushing Kit
starstarstarstarstar (5)
$90
ARB / OME Frontier / Xterra Rear Leaf Spring Bushing Kit - OE Shackle
starstarstarstarstar (3)
$31
ARB / OME Frontier / Xterra Rear Leaf Spring Bushing Kit -GS15 Shackle
starstarstarstarstar (3)
$32
Prothane Nissan / Infiniti Front Sway Bar Bushings - Red (Pair)
$14.97
Whiteline Frontier / Pathfinder / Xterra Steering Rack Bushing Kit
$41.88
Prothane Nissan / Infiniti Front Sway Bar Bushings - Black (Pair)
starstarstarstarstar_border (1)
$14.97
starstarstar_borderstar_borderstar_border
Kiyomi
January 5, 2023
It took over 5 tons of pressure in a press to push this flat and it still popped back out of the last rib. Only buy if you’re willing to manipulate the product; I ended up cutting off the last 2 ribs for it to fit flush enough to mount back onto the shock strut. No fault of Z1 at all.
starstarstarstarstar
Malachi
December 5, 2022
I struggled to install these for 20 minutes pressing them and each time they backed out. I decided to press them without the metal sleave and they slipped in like a charm. The bushing needs room for play when being pressed. Afterwards I pressed the sleeve in, and I was good to go. Super easy.
starstarstarstar_borderstar_border
Eric
July 4, 2021
These are great, but the reason for the three stars is that it's very hard to insert the inner bushing into the outer bushing. If you end up do buying them, I'd recommend shaving down the humps on the inner bushing or you'll have a lot of fun trying to fit in the last two ridges into the outer bushing.
starstarstarstarstar_border
Stephen
March 15, 2021
Service from Z1 was great as always. As supplied these suckers are too good for their homes. Dry, lubed, left in the press for a couple of calm down smokes, these suckers pop back out a rib. Used a resurfacing pad to take off material from the inner bush and it cooperated. Bushings haven't tried to squish out any after installation and I don't think this new design will pound out and split after 3 years like the old equal halves ES bushes did.
starstarstarstar_borderstar_border
Bradley
June 29, 2017
These bushings are VERY difficult to install. I called Z1 to see if I was missing something or doing something wrong... They informed me they are tough and I was not doing anything wrong. They typically use washers and a vice to pop them in. Z1 informed me that Energy Suspension changed to this design a few years back.
The issue is the inner bushing will not, seat into the outer bushing. You would put it in a press, it would look great, but when you pull the press back the bushings were still not together.
Ultimately, I trimmer the end of the inner bushing and cut down a few of the ribs. That was the only way I could get it in. The metal sleeve does not have as much surface area now so I do not know how much that will reduce the life of the bushings. When they go, I will just put some spherical bearings in there.
Z1 was awesome. I called them and were super knowledgeable and helpful. That is why the rating is neutral. Bushing would not go together without modification, but Z1 was great.
ASRIUBNFAIURNFKAJSNFLAKJSDNFLKASNDFLKASDNMFALKSNDFOANEF