Product Description
Z1 Motorsports Stainless Steel Clutch Line for all '09+ 370z and '08+G37 models
This is a must have upgrade for any 370z/G37 with an upgraded clutch and/or that sees track usage. This will eliminate the mushy pedal feel, that ALL Z/G's have after installing high clamping force clutches. The kit works wonders with Dual and Triple Disc clutches as well. By eliminating all soft points in your hydraulic system, it adds to pedal response and feel. This line also deletes an additional 6" of metal clutch line on the side of the bell housing, eliminating a potential leak point in the clutch system.
The new Z1 Braided Stainless Steel clutch line features a special vinyl coating that protects it from fraying caused by rubbing or vibrations. The 370Z / G37 clutch line features a black vinyl coating with an insulated reflective thermal sleeve that not only looks great but also protects your line from rubbing, fraying and radiant heat damage from turbos, exhausts, and other nearby heat sources. It also comes with a new banjo bolt and 2 copper washers to insure a trouble free install.
Please note:
Z1 Motorsports ONLY recommends the usage of Motul RBF 600 Brake/Clutch Fluid for 370z/G37 Hydraulic Clutch System.
*** This item does not qualify for any additional discounts or promotions *** |
 |
OEM Clutch Pressure Plate Bolt Washer
starstarstarstarstar (3)
$2.80
Red Line MT-85 GL-4 Manual Transmission Gear Oil - 1qt
starstarstarstarstar_half (16)
$23.10
Motul RBF 600 Brake Fluid
starstarstarstarstar_half (15)
$20.46
OEM Long Life Blue Coolant (Antifreeze) - 50/50 Pre-Mixed
starstarstarstarstar (57)
$19.32
Motul RBF 660 Performance Brake Fluid
starstarstarstarstar (2)
$28.08
OEM Nissan Fluid Gasket (RTV)
starstarstarstarstar_half (37)
$11.59
Do you have an install guide?
Seems like it should be straight forward, however, my 2016z (sport) does not have a banjo where it attaches to the slave, the current metal cable has a female connector, the CSC has is a male fitting. Can send pictures if needed.
Am I supposed to disassemble part of the CSC to convert to a banjo?
Dave
[email protected]We replace the factory soft clutch line and the hard tube that goes into the CSC tube. You will install the line and banjo straight directly to the block near the bleeder.
Frontier / Xterra VK56 Swap Clutch & Flywheel Kit by Z1 Off-Road
starstarstarstarstar (1)
$754.99
2 Bolt Exhaust Gasket
starstarstarstarstar_half (38)
$7.99
Z1 Metal 2 Bolt Exhaust Gaskets
starstarstarstarstar_half (44)
$14.99
CNC Aluminum Hub Centric Wheel Spacers 2.5, 5, 10, 15, & 20mm
starstarstarstarstar_half (34)
$20.25
Z1 10mm Ratcheting Keychain Wrench
starstarstarstarstar (25)
$9.99
Z1 Key Tag
starstarstarstarstar_half (21)
$3.99
starstarstarstarstar
Andrew
May 22, 2024
nice that it replaces part of the metal factory line, right into slave. thought it was wrong at first, then lo and behold - bam. right thing.
starstarstarstarstar
Nikolay
July 21, 2023
Quality piece to replace the stock rubber clutch line. Also removes the short metal line and from the outside of the transmission.
starstarstarstarstar
Steve
May 31, 2023
work great, better than the cheap original . must get
starstarstarstarstar
Danielito
November 11, 2021
Clutch pressure is perfect
starstarstarstarstar
Nathaniel
June 6, 2021
I purchased this as an upgrade, along with a bottle of Motul RBF 600, because of a soft clutch pedal feeling occurring after a few laps on the track. During installation, I opted to double-wrap this with the factory insulation for extra heat protection, since it is near the exhaust. Installation was a bit tricky, and I ended up going through the front left wheel house to help access the upper connection. However, it is entirely possible to do without dropping the exhaust.
While the problem was most likely boiling/cavitation caused by degradation and water absorption of the old fluid, it does seem that pedal feel is generally slightly improved by the stainless line. This seems to be a worthwhile upgrade for the Z. Just be sure to refill with high-temperature fluid, as that will make the biggest difference.
starstarstarstar_borderstar_border
Tyler
February 14, 2018
mine burst after about 2 or 3 months and I even wrapped it with the factory reflective wrap from the stock line. Rubber factory hose is fine for a stock clutch. it was way more consistent, still it burst
ASRIUBNFAIURNFKAJSNFLAKJSDNFLKASNDFLKASDNMFALKSNDFOANEF